This is why thousands of depend on us to provide the best 70-741 the most cheap training. If your budget 70-741 is limited, you need to complete solutions. Don’t rely on free 70-741 learning guidance or expensive 70-741 training guidelines.Many IT professionals prefer to add exam Microsoft among their credentials. The Microsoft strengthens the employment prospects and opens up myriads of opportunities for them. Examgood not only Microsoftters you all the information regarding the exam Microsoft but also provides you the excellent Microsoft MCSA 70-741 exam practice test which makes the Microsoft exam easy for you.
Share some MCSA 70-741 exam questions and answers below.
You have a DHCP server named Server1 that runs Windows Server 2016.

You have a single IP subnet.

Server1 has an IPv4 scope named Scope1. Scope1 has an IP address range of 10.0.1.10 to 10.0.1.200 and a length of 24 bits.

You need to create a second logical IP network on the subnet. The subnet will use an IP address range of 10.0.2.10 to 10.0.2.200 and a length of 24 bits.

What should you do?

A. Create a second scope, and then create a superscope.

B. Create a superscope, and then configure an exclusion range in Scope1.

C. Create a new scope, and then modify the IPv4 bindings.

D. Create a second scope, and then run the DHCP Split-Scope Configuration Wizard.

Answer: A

Note: This question is part of a series of questions that use the same or similar answer choices. An answer choice may be correct for more than one question in the series. Each question is independent of the other questions in this series. Information and details provided in a question apply only to that question.

Your network contains Windows and non-Windows devices.

You have a DHCP server named Server1 that has an IPv4 scope named Scope1.

You need to prevent a client computer that uses the same name as an existing registration from updating the registration.

What should you do?

A. From the properties of Scope1, modify the Conflict detection attempts setting.

B. From the properties of Scope1, configure Name Protection.

C. From the properties of IPv4, configure the bindings.

D. From IPv4, create a new filter.

E. From the properties of Scope1, create an exclusion range.

F. From IPv4 run the DHCP Policy Configuration Wizard.

G. From Control Panel, modify the properties of Ethernet.

H. From Scope1, create a reservation.

Answer: F

Your network contains an Active directory forest named contoso.com. The forest has a Distributed File System (DFS) namespace named \contoso.comnamespace1.

The domain contains a file server named Server1 that runs Windows Server 2016.

You create a folder named Folder1 on Server1.

Which two cmdlets should you use? Each correct answer presents part of the solution.

NOTE: Each correct selection is worth one point.

A. New-DfsnFolderTarget

B. Install-WindowsFeature

C. Grant-DfsnAccess

D. New-DfsnFolder

E. New-SmbShare

Answer: BC

You have a virtual machine named VM1 that runs Windows Server 2016, VM1 hosts a service that requires high network throughput.

VM1 has a virtual network adapter that connects to a Hyper-V switch named vSwitch1. vSwitch1 has one network adapter. The network adapter supports Remote Direct Memory Access (RDMA), the single root I/O virtualization (SR-IOV) interface, Quality of Service? (QoS), and Receive Side Scaling (RSS).

You need to ensure that the traffic from VM1 can be processed by multiple networking processors.

Which Windows PowerShell command should you run on the host of VM1?

A. Set-NetAdapterRss

B. Set-NetAdapterRdma

C. Set-NetAdapterQos

D. Set-NetAdapterSriov

Answer: D

You are implementing a new network. The network contains a DHCP server named DHCP1 that runs Windows Server 2016. DHCP1 contains a scope named Scope1 for the 192.168.0/24 subnet.

Your company has the following policy for allocating IP addresses:

•All server addresses must be excluded from DHCP scopes.

•All client computer must receive IP addresses from Scope1.

•All Windows servers must have IP addresses in the range of 192.168.0.200 to 192.168.0.240

•All other network devices must have IP addresses in the range of 192.168.0.180 to 192.168.0.199.

You deploy a print device named Print1.

You need to ensure that Print1 adheres to the policy for allocating IP addresses.

Which command should you use?

A. Add-DhcpServerv4Lease

B. Add-DhcpServerv4ExclusionRange

C. Add-DhcpServerv4Filter

D. Add-DhcpServerv4Reservation

Answer: B

They provide a very effective training tools and online services for your. If you want to buy Examgood products, Examgood will provide you with the latest, the best quality and very detailed training materials as well as a very accurate exam practice questions and answers to be fully prepared for you to participate in the Microsoft certification 70-741 exam. Safely use the Microsoft MCSA 70-741 exam practice test provided by Examgood.

Microsoft 70-741 certification exam is very important for every IT person. With this certification you will not be eliminated, and you will be a raise. Some people say that to pass the Microsoft 70-741 certification is tantamount to success. Yes, this is true. You get what you want is one of the manifestations of success. Examgood of Microsoft 70-741 exam materials is the source of your success. With this training materials, you will speed up the pace of success, and you will be more confident.

Examgood is an excellent source of information on IT Certifications. At Examgood, you can find study tips as well as study materials for your preparation of certification exam. Examgood 70-741 exam can add your confidence in achieving your goal. Examgood Microsoft MCSA 70-741 exam practice test is the best toll to prepare for your 70-741 certification exam. Producing software that our clients never need to re-purchase is a commitment 70-741 exam that we have upheld for 30 years. MCSA are real career booster and they also spark your career and provide you many golden opportunities to enhance your career and professional expertise.

Leave a Reply

Your email address will not be published. Required fields are marked *

*